建设专业网站的利弊,自由设计师如何接单,西凤酒网站建设的基本情况,网站建设 cms一、拓扑图#xff1a;二、配置各路由器的IP和EIGRP 协议#xff0c;并保证邻接关系的形成。1、我要达到的目的是要让R2到192.168.14.0/24这个网段能在R2和R1断开之后#xff0c;形成网网络的快速收敛。因为根据EIGRP 的次优路径进拓扑关系的形成条件是要满足FC#xff08;… 一、拓扑图 二、配置各路由器的IP和EIGRP 协议并保证邻接关系的形成。 1、我要达到的目的是要让R2到192.168.14.0/24这个网段能在R2和R1断开之后形成网网络的快速收敛。因为根据EIGRP 的次优路径进拓扑关系的形成条件是要满足FCfeasible conditionFDfeasible distanceAD(通告距离也就是下一跳路由器到目的网段这一距离)。这个条件也是为什么EIGRP是100%无环路的原因。现在我们看一下R2的EIGRP 拓扑 R2#show ip eigrp to IP-EIGRP Topology Table for AS(100)/ID(192.168.23.2) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.34.0/24, 1 successors, FD is 2172416 via 192.168.23.3 (2172416/28160), Serial0/1 P 192.168.12.0/24, 1 successors, FD is 28160 via Connected, FastEthernet1/0 P 192.168.14.0/24, 1 successors, FD is 2172416 via 192.168.12.1 (2172416/2169856), FastEthernet1/0 P 192.168.23.0/24, 1 successors, FD is 2169856 via Connected, Serial0/1 R2# 2、通过上面的topology我们看到R2有一个Ppassive到192.168.14.0只有一条FD。那么我们想什么办法去满足在R2上形成FDAD。把次优路径放进拓扑中让EIGRP在另一条链路DOWN 后形成一个快速收敛的过程。我们在R2上看到这么一条 P 192.168.14.0/24, 1 successors, FD is 2172416 via 192.168.12.1 (2172416/2169856), FastEthernet1/0 下面再看一下R3 R3#sho ip eigrp to IP-EIGRP Topology Table for AS(100)/ID(192.168.34.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.34.0/24, 1 successors, FD is 28160 via Connected, FastEthernet1/0 P 192.168.12.0/24, 1 successors, FD is 2172416 via 192.168.23.2 (2172416/28160), Serial0/1 P 192.168.14.0/24, 1 successors, FD is 2172416 via 192.168.34.4 (2172416/2169856), FastEthernet1/0 P 192.168.23.0/24, 1 successors, FD is 2169856 via Connected, Serial0/1 R3# R2#show ip protocols Routing Protocol is eigrp 100 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Outgoing routes in FastEthernet1/0 will have 1 added to metric if on list 1 Incoming routes in FastEthernet1/0 will have 1 added to metric if on list 1 Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K11, K20, K31, K40, K50 EIGRP maximum hopcount 100 EIGRP maximum metric variance 2 (现在变成2了) Redistributing: eigrp 100 EIGRP NSF-aware route hold timer is 240s Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 192.168.12.0 192.168.23.0 Routing Information Sources: Gateway Distance Last Update 192.168.12.1 90 00:25:56 192.168.23.3 90 00:25:56 Distance: internal 90 external 170 4、 我们再看一下R2的路由 R2#show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set C 192.168.12.0/24 is directly connected, FastEthernet1/0 D 192.168.14.0/24 [90/2684416] via 192.168.23.3, 00:29:04, Serial0/1 [90/2172417] via 192.168.12.1, 00:29:04, FastEthernet1/0 C 192.168.23.0/24 is directly connected, Serial0/1 D 192.168.34.0/24 [90/2172416] via 192.168.23.3, 00:29:04, Serial0/1 D 192.168.1.0/24 [90/156160] via 192.168.12.1, 00:29:04, FastEthernet1/0 R2# 看到了有两条路径可以走了也就是实现了EIGRP 非等价负载均衡。 五、分析一下非等价负载均衡包的转发情况 1、我先在R2上关上cef 包交换 R2(config)#no ip cef 2、 我再来看一下到192.168.14.0路径的路由情况 R2#show ip route 192.168.14.0 Routing entry for 192.168.14.0/24 Known via eigrp 100, distance 90, metric 2172417, type internal Redistributing via eigrp 100 Last update from 192.168.23.3 on Serial0/1, 00:37:03 ago Routing Descriptor Blocks: 192.168.23.3, from 192.168.23.3, 00:37:03 ago, via Serial0/1 Route metric is 2684416, traffic share count is 97 Total delay is 40100 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2 * 192.168.12.1, from 192.168.12.1, 00:37:03 ago, via FastEthernet1/0 Route metric is 2172417, traffic share count is 120 Total delay is 20100 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 3、 根据上面的情况我看到了R2到192.168.14.0先走192.168.12.1转发120个count然后再会走192.168.23.3 再转发97个count。正是因为一个转120 count一个转97 count,我想也就是叫非等价的原因。 3、我们看到了 P 192.168.14.0/24, 1 successors, FD is 2172416 via 192.168.34.4 (2172416/2169856), FastEthernet1/0 EIGRP 改COST值如果改带宽改K值这样会影响整个链路。如果只想把一条路径加进topology。这样我们只要R3到192.168.14.0 的FD如果形成次路径此段也就是R2到192.168.14.0的AD让它满足小于R2到192.168.14.0 的FD。即FDAD.就会把这条链路放进拓扑中。 三、下面可以用offset list命令偏移cost 值。把R2到192.168.14.0 这一段改大我们可以在R1的出口或者是R2的进口来做。但要注意改大cost值对链路是没影响的因为它还是处于passive 状态但如果把链路改小的话它会有一个active 的过程。这个在TCP/IP卷里面有详细说明。 1、下面我在R1上做一个out方向来启用offset : R1(config)#access-list 1 permit 192.168.12.0 0.0.0.255(通告192.168.14.0给R2时调用这cost ) R1(config)#router eigrp 100 R1(config-router)#offset-list 1 out 1 fastEthernet1/0 (我让它在R1的F1/0这个出口上调用上access-list 1) 2、OK,现在R2到192.168.14.0/24的FD偏移了1变成了2172417。 R2#show ip eigrp topology IP-EIGRP Topology Table for AS(100)/ID(192.168.23.2) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.34.0/24, 1 successors, FD is 2172416 via 192.168.23.3 (2172416/28160), Serial0/1 P 192.168.12.0/24, 1 successors, FD is 28160 via Connected, FastEthernet1/0 P 192.168.14.0/24, 1 successors, FD is 2172417 via 192.168.12.1 (2172417/2169857), FastEthernet1/0 via 192.168.23.3 (2684416/2172416), Serial0/1 (这个值就是R2到192.168.14.0的AD) P 192.168.1.0/24, 1 successors, FD is 156160 via 192.168.12.1 (156160/128256), FastEthernet1/0 P 192.168.23.0/24, 1 successors, FD is 2169856 via Connected, Serial0/1 四、在R2上实现非等价负载均衡 1、通过偏移cost值之后下面我们再看一下R2的路由表 R2#show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set C 192.168.12.0/24 is directly connected, FastEthernet1/0 D 192.168.14.0/24 [90/2172417] via 192.168.12.1, 00:10:52, FastEthernet1/0 C 192.168.23.0/24 is directly connected, Serial0/1 D 192.168.34.0/24 [90/2172416] via 192.168.23.3, 00:10:52, Serial0/1 D 192.168.1.0/24 [90/156160] via 192.168.12.1, 00:10:53, FastEthernet1/0 2、通过上面的显示情况R2到192.168.14.0这个网段是走R2这条路径过去因为偏移只是把次路径放入topology并没有放入路由表那么我现在想让它放入路由表这样可以实现通过两条路径到192.168.14.0。有效的实现了非等价负载均衡。但是必须要让它满足一个条件就是R2 的successor(FD)×variance 值≥Feasible Successor缺省情况下variance 等于1这样就是等价均衡我只要把R2上面FD乘以2就能形成非等价负载均衡 R2(config)#router eigrp 100 R2(config-router)#variance 2 3、 通过上面的修改我们现在再看一下R2的variance : 转载于:https://blog.51cto.com/supercisco/248232
